Conductor Supports for Sale
T4033240
CHANCE® Compact Telescoping Disconnect Stick, 11 ft.- Tested per OSHA & ASTM F711
- Allow linemen to perform many routine jobs from ground level
- Universal end fitting on insulated top section accepts a wide variety of attachments
- This allows lineman to disconnect switches and replace cutout tubes
- Also allows lineman to remove pole covers, prune trees, plus other overhead tasks
- Sticks retract to approximately 5 ft. for easy truck transport (even in most cab sections)
- Heavy-duty, spring-loaded plastic buttons keep extended tool sections locked in place
- As each section extends and slightly twists, buttons also pop securely into place
Your Price:
REQUEST
T4002530
CHANCE® Jib Accessory " The Pickle Head" Wireholder/Rope Sheave Combo 800 lb. Capacity- Eliminates changeovers from Wireholder (for picking up a phase conductor) to Rope Sheave (for lifting items)
- Each combination unit attaches directly to jib
- Rated Working Load: Wireholder - 300 lbs. Sheave - 800 lbs.
- Both units feature a Large SwivelType Roller Wireholder with 2-½" x 3-3⁄8" opening and a 7"-dia. Sheave to accept up to 3⁄4"-dia. rope
Your Price:
REQUEST
T4001940
CHANCE® One Conductor Support, 30"- For use during replacement of poles or repair/ replacement of pole top and stand-off insulators
- Fork-type wireholder accepts up to 1”-diameter conductor
- Working load: 150 lb. per wireholder on T4001939 only
- Works well even with rubber gloves and leather protectors
- Epoxiglas® temporary conductor support is used to hold energized distribution conductors
Your Price:
REQUEST
T4001939
CHANCE® Two Conductor Supports, 48"- Hanging a temporary conductor support involves just hooking buckle in clasp on bracket and cinching the strap with ratchet handle
- Wide handle opening on rapid-action ratchet permits easy operation
- Works well even with rubber gloves and leather protectors
- For use during replacement of poles or repair/ replacement of pole top and stand-off insulators
- Fork-type wireholder accepts up to 1”-diameter conductor
- Working load: 150 lb. per wireholder on T4001939 only
Your Price:
REQUEST
NLDE2506CLVST
CTOS Dead End Arms w/ Clover Head or Butt Swivel- Standard or Large
- 2.50” Diameter Fiberglass
- Load Limit: 500lbs per position, 1000lbs total load
- Accommodates up to 5/8” hardware and wire
- Maximum Crossarm Height: 6-1/8” (ST) and 8-3/8" (LG)
- Insulating value of 100kV per foot dry, 75kV per foot wet
- Standard Package: 1
- Minimum Order Qty: 1
- Built to meet or exceed all applicable ASTM and OSHA standards, including F711
Your Price:
REQUEST
NL3490D
CTOS Heavy-Duty Distribution Extension Arm - 6' x 2.5"- Strongest fiberglass in the industry
- Stainless Steel components
- UHMW Hanger - will not damage arm
- UHMW End Cap - less overall damage
- Fits all applications - Universal Arm
- Highest load rating of any arm
- High impact epoxy finish
- 6-feet with a 2.50” Diameter Thick-Walled Fiberglass
- Available with or without insulator
- Part Number(s): NL3489D, NL3490D
Your Price:
REQUEST
NL3490T
CTOS Heavy-Duty Transmission Extension Arm - 6' x 2.5"- Strongest fiberglass in the industry
- Stainless Steel components
- UHMW Hanger - will not damage arm
- UHMW End Cap - less overall damage
- Fits all applications - Universal Arm
- Highest load rating of any arm
- High impact epoxy finish
- 6-feet with a 2.50” Diameter Thick-Walled Fiberglass
- Available with or without insulator.
- Part Number(s): NL3489T, NL3490T
Your Price:
REQUEST
NL3490U
CTOS Heavy-Duty Universal Extension Arm - 6' x 2.5"- Strongest fiberglass in the industry
- Stainless Steel components
- UHMW Hanger - will not damage arm
- UHMW End Cap - less overall damage
- Fits all applications - Universal Arm
- Highest load rating of any arm
- High impact epoxy finish
- 6-feet with a 2.50” Diameter Thick-Walled Fiberglass
- Part Number(s): NL3490U
Your Price:
REQUEST
NL2356
CTOS Single Conductor Pole-Mounted Temporary Support - 3' x 2.5"- Strongest fiberglass in the industry
- Stainless Steel components
- Largest base - biggest footprint
- UHMW End Cap - less overall damage
- Overbuilt strap - no slippage
- Highest load rating of any arm
- High impact epoxy finish
- Available with or without insulator
- Dimensions: 3' x 2.5"
- Part Number(s): NL2355, NL2356
Your Price:
REQUEST
NL2455
CTOS Two Conductor Pole-Mounted Temporary Support - 4' x 2.5"- Strongest fiberglass in the industry
- Stainless Steel components
- Largest base - biggest footprint
- UHMW End Cap - less overall damage
- Overbuilt strap - no slippage
- Highest load rating of any arm
- High impact epoxy finish
- Available with or without insulator
- Dimensions: 3' x 2.5"
- Part Number(s): NL2455, NL2456
Your Price:
REQUEST
5054
Hastings 81" temporary cross arm- The Temporary Cross Arm is an excellent tool for changing cross arms. Solid fiberglass arms for maximum strength.
- Rated for 34.5KV phase to phase.
- Two piece assembly makes installation easy and fast
- Mounting base includes a ratchet and strap assembly for lightweight and safety
- U-Shape design fits over pole top pin.
- Fiberglass arm includes two standard conductor holders A10002 with insulators and will accept conductors up to 1 1/16” O.D. Conductor latches are hot stick operable.
- Also available A10039 Large Conductor Holder - 2 5/8” opening
- Load limit is 150 pounds per side
Your Price:
REQUEST
3465
Hastings Conductor Tension Tool, 69KV- 72" to 84" working range
- 12" maximum take up
- Length stored: 74"
- Length extended: 86"
- Load limit 4,000 lbs.
- Tension tool can be installed and operated using hot sticks
- Two models available
- Conductor hooks have hot stick eyes and hot stick operable safety latches. Hooks are stationary.
- Metal components are heat treated aluminum alloy or bronze alloy
Your Price:
REQUEST
7545
Hastings Super U Arm Extensions and Replacement Parts- All arms include insulated conductor holders to insure dielectric integrity. Arms are rated for 34.5KV phase-to-phase work applications.
- Arms with the standard conductor holder will accept conductors up to 1 1/16” O.D. or up to 800 MCM.
- Arms with large capacity conductor holder, can accommodate a conductor inside a line hose. The gate latch on the large capacity holder has an opening of 2 5/8”.
- The Super “U” design is stronger than the traditional style round extension arms. All Super “U” Arms and Super “U” Conductor Supports have a load limit of 200 lbs. per wire holder.
- Interchangeable hanger loop kits are available for the different sizes of cross arms on your system.
Your Price:
REQUEST
7674
Hastings Temporary Dead End Arm- ARM WITH 3 WAY BRACKET
- Height Adjustments: 4 5/8”, 4 7/8”, 5 7/8”, 6 1/8”
- Width Adjustments: 3 7/8”, 5”, 6 1/8” (7674 & 7675) or 6 1/8", 7 1/4", 8 3/8" (7676).
- Arms are constructed with 3” diameter fiberglass and a foam core to meet most load requirements for
- temporary dead ends.
- Load limit - 500 lbs. per position or 1,000 lbs. total load limit.
- Arms have two holes with 18” spacing to accommodate 5/8” diameter hardware bolts for dead ends.
- Two aluminum sleeves are installed to prevent wear on the fiberglass arm.
Your Price:
REQUEST